Four-panel comic: a frosted wheel loader on a cold morning, thick cold oil pouring slowly, the loader warming up at sunrise, then working in the snow.

Hydraulic Motor Cold Start: Warm the Oil Before You Load the Motor

Field Note Failure & Maintenance

First frost:
warm the oil before you load the motor.

On a cold morning the same motor starts its day under very different conditions. A start-up routine and a pre-season check that keep winter starts from turning into winter repairs.

Four-panel comic: a frosted wheel loader on a cold morning, thick cold oil pouring slowly, the loader warming up at sunrise, then working in the snow.
The winter start-up routine in four panels.

When temperatures drop, hydraulic oil thickens, and the first minutes after a cold start are when a low-speed high-torque motor is most exposed. Operators naturally want to get in and go.[1] Winter care is less about changing the motor and more about the conditions it starts in.

01Cold oil

What cold does inside the circuit

Viscosity rises as oil temperature falls, and oil that is too thick restricts flow at the pump inlet. Pressure there drops until the oil starts to vaporize, which is why cavitation is described as the main issue with cold oil.[3] At the motor, the same extremes mean possible cavitation and loss of lubrication in the cold.[2]

For this reason pump and motor manufacturers publish limits that include a maximum start-up viscosity under load.[4] Even a light ISO VG 15 oil can be thick in severe cold.[1]

Takeaway

Compare the start-up viscosity limit in your pump and motor catalogs with your oil at the lowest temperature the machine will see.

02Start-up

A cold start-up routine

  1. Heat the oil first. Thermostatically controlled tank heaters, or a heat exchanger on engine coolant with a warm-up bypass circuit, bring the oil up before work starts.[1]
  2. Warm up without load. Run at low speed and no load until the oil is back in its working viscosity range, then apply load. A cold machine should be warmed up, not only a hot one cooled down.[2]
  3. Make sure the case is full. Use the uppermost drain port and fill the case with oil before the first start, so the motor never starts dry.[2]
  4. Respect the case drain. Route drain lines with their sensitivity to back pressure in mind.[1] Cold, thick oil in a shared return line is one more reason to give the drain its own line to tank.
03Pre-season

Before the season starts

Oil. A single-grade oil that starts well in the cold can run dangerously thin at operating temperature, especially if it is not changed for summer. A synthetic oil with a high viscosity index covers both: a decent hydraulic oil has a VI over 100, and the best arctic oils reach 200 or more.[1]

Water. Cold oil holds less water, and free water that freezes can damage internal parts. Sealed reservoirs with mild pressurization and dry oil at fill help keep it out,[1] as do desiccant breathers.[2]

Seals. Choose seal materials that stay stable in the cold, such as HNBR, FKM and certain polyurethanes.[1]

04FAQ

Common questions

How long should a hydraulic motor warm up in winter?
There is no single time. Run at low speed with no load until the oil is back in the working viscosity range given in the pump and motor catalogs, then apply load. A tank heater shortens the wait.
Can I simply use a thinner oil in winter?
A thinner oil helps the machine start, but it can run too thin once the system reaches operating temperature, especially in all-season machines. A high viscosity index oil covers a wider temperature range.
Talk to the engineers

Planning a winter set-up?

Tell us the lowest ambient temperature, the oil you use and the motor model. Our engineers will review the operating conditions for that model.

Email sales20@zihyd.com →See the LinkedIn post →
References
  1. [1]J. Cosford, “Designing your hydraulic systems for winter,” Fluid Power World, 20 January 2026. fluidpowerworld.com
  2. [2]J. Cosford, “7 steps to prevent hydraulic motor failure,” Fluid Power World, 11 July 2025. fluidpowerworld.com
  3. [3]J. Pasko, “The Role of Temperature Control in Hydraulic Oil Reliability,” Precision Lubrication, January 2023. precisionlubrication.com
  4. [4]“The Benefits of Maximum Efficiency Hydraulic Fluids,” Machinery Lubrication. machinerylubrication.com